Unite element slip analysis of multi layer beam plate based on a composite theory

T. Takagi; K. Miya; Y. Takeuchi; J. Tani

doi:10.1016/S0920-3796(88)80017-6

Unite element slip analysis of multi layer beam plate based on a composite theory

T. Takagi, K. Miya, Y. Takeuchi, J. Tani

Research output: Contribution to journal › Article › peer-review

1 Citation (Scopus)

Abstract

A formulation of elastoplastic stress analysis of the laminated structure is shown on the basis of the finite element method using the assumptions of Voigt and Reuss. Systematic tests were carried out at room temperature with specimens composed of stainless steel and epoxy resin to depict a slip curve representing the interface strength. Three and four point bending tests were performed to verify the validity of the composite theory developed here. The data on the strength of separation were used in the numerical analyses. Comparison of the numerical results and experimental results are fairly good.

Original language	English
Pages (from-to)	255-267
Number of pages	13
Journal	Fusion Engineering and Design
Volume	7
Issue number	C
DOIs	https://doi.org/10.1016/S0920-3796(88)80017-6
Publication status	Published - 1988
Externally published	Yes

ASJC Scopus subject areas

Civil and Structural Engineering
Nuclear Energy and Engineering
Materials Science(all)
Mechanical Engineering

Access to Document

10.1016/S0920-3796(88)80017-6

Cite this

@article{81b4ac1004b04aecbffdbd0dfe642c31,

title = "Unite element slip analysis of multi layer beam plate based on a composite theory",

abstract = "A formulation of elastoplastic stress analysis of the laminated structure is shown on the basis of the finite element method using the assumptions of Voigt and Reuss. Systematic tests were carried out at room temperature with specimens composed of stainless steel and epoxy resin to depict a slip curve representing the interface strength. Three and four point bending tests were performed to verify the validity of the composite theory developed here. The data on the strength of separation were used in the numerical analyses. Comparison of the numerical results and experimental results are fairly good.",

author = "T. Takagi and K. Miya and Y. Takeuchi and J. Tani",

note = "Funding Information: The numerical code was made with the financial support of IPL, Nagoya University and the authors obtained helpful suggestions from Prof. Abe of the University, Dr. T. Watanabe and Mr. K. Tagata and CRC. Funding Information: The experimental work has been done with the financial support of the Controlled Thermonuclear Reactor Committee (Chairman, Prof. Y. Takahashi), Faculty of Engineering, The University of Tokyo.",

year = "1988",

doi = "10.1016/S0920-3796(88)80017-6",

language = "English",

volume = "7",

pages = "255--267",

journal = "Fusion Engineering and Design",

issn = "0920-3796",

publisher = "Elsevier BV",

number = "C",

}

TY - JOUR

T1 - Unite element slip analysis of multi layer beam plate based on a composite theory

AU - Takagi, T.

AU - Miya, K.

AU - Takeuchi, Y.

AU - Tani, J.

N1 - Funding Information: The numerical code was made with the financial support of IPL, Nagoya University and the authors obtained helpful suggestions from Prof. Abe of the University, Dr. T. Watanabe and Mr. K. Tagata and CRC. Funding Information: The experimental work has been done with the financial support of the Controlled Thermonuclear Reactor Committee (Chairman, Prof. Y. Takahashi), Faculty of Engineering, The University of Tokyo.

PY - 1988

Y1 - 1988

N2 - A formulation of elastoplastic stress analysis of the laminated structure is shown on the basis of the finite element method using the assumptions of Voigt and Reuss. Systematic tests were carried out at room temperature with specimens composed of stainless steel and epoxy resin to depict a slip curve representing the interface strength. Three and four point bending tests were performed to verify the validity of the composite theory developed here. The data on the strength of separation were used in the numerical analyses. Comparison of the numerical results and experimental results are fairly good.

AB - A formulation of elastoplastic stress analysis of the laminated structure is shown on the basis of the finite element method using the assumptions of Voigt and Reuss. Systematic tests were carried out at room temperature with specimens composed of stainless steel and epoxy resin to depict a slip curve representing the interface strength. Three and four point bending tests were performed to verify the validity of the composite theory developed here. The data on the strength of separation were used in the numerical analyses. Comparison of the numerical results and experimental results are fairly good.

UR - http://www.scopus.com/inward/record.url?scp=38149144748&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=38149144748&partnerID=8YFLogxK

U2 - 10.1016/S0920-3796(88)80017-6

DO - 10.1016/S0920-3796(88)80017-6

M3 - Article

AN - SCOPUS:38149144748

SN - 0920-3796

VL - 7

SP - 255

EP - 267

JO - Fusion Engineering and Design

JF - Fusion Engineering and Design

IS - C

ER -

Unite element slip analysis of multi layer beam plate based on a composite theory

Abstract

ASJC Scopus subject areas

Access to Document

Other files and links

Fingerprint

Cite this