Kenta Yamanaka

Scopus著者プロファイル

h-index

年別の研究成果

フィンガープリント

Kenta Yamanakaが活動している研究トピックを掘り下げます。このトピックラベルは、この研究者の研究成果に基づきます。これらがまとまってユニークなフィンガープリントを構成します。

1 類似のプロファイル

156 学術論文
4 会議への寄与
1 章
1 コメント/討論
その他
- 1 総説

Preparation of recycled zirconia powders for use in esthetic dental restorations by wet ball milling technique
Yang, H., Yamanaka, K., Mori, M., Shishido, S., Sáenz, J. R. V., Nakamura, K. & Guang, H., 2026 1月 31, In: Powder Technology. 468, 121688.
研究成果: ジャーナルへの寄稿 › 学術論文 › 査読

Open Access
A novel two-step process for enhancing adhesion strength of cold-spray metallization of carbon fiber-reinforced plastics
Sun, J., Yamanaka, K., Bernard, C. A. R. M., Lei, Y., Zhou, S., Lin, H., Ogawa, K. & Chiba, A., 2025 1月, In: Materials and Design. 249, 113568.
研究成果: ジャーナルへの寄稿 › 学術論文 › 査読

Open Access
5 被引用数 (Scopus)
Comparative evaluation of powder spreading strategies to enhance powder bed quality in powder bed fusion additive manufacturing: A DEM simulation study
Yim, S., Wang, H., Aoyagi, K., Yamanaka, K. & Chiba, A., 2025 3月 15, In: Powder Technology. 453, 120614.
研究成果: ジャーナルへの寄稿 › 学術論文 › 査読

Open Access
5 被引用数 (Scopus)
Comparative study on the microstructural evolution and performance of Cu-5Ag wires during cold-drawing from powder metallurgy and cast states
Zhou, Y., Gong, X., Zhang, P., Tang, N., Yamanaka, K., Chiba, A. & Li, Y., 2025 5月, In: Materials Science and Engineering: A. 929, 148055.
研究成果: ジャーナルへの寄稿 › 学術論文 › 査読
3 被引用数 (Scopus)
Design and characterization of novel Ti-8Mo-xFe-yCu alloys as implant materials: Evaluation of biocompatibility, mechanical properties, and antibacterial potential
Senopati, G., Rashid, R. A. R., Juliadmi, D., Prastya, M. E., Mori, M., Yamanaka, K., Kartika, I. & Palanisamy, S., 2025 11月, In: Materials Science and Technology (United Kingdom). 41, 16, p. 1177-1190 14 p.
研究成果: ジャーナルへの寄稿 › 学術論文 › 査読
3 被引用数 (Scopus)

Investigators at Tohoku University Report Findings in Additive Manufacturing (Effect of Powder Morphology On Flowability and Spreading Behavior In Powder Bed Fusion Additive Manufacturing Process: a Particle-scale Modeling Study)
Yamanaka, K., Chiba, A. & Yim, S.
23/8/8
1 次の項目: メディア掲載
プレス/メディア
Researchers from Tohoku University Publish Research in Materials and Design (Competition between solid solution and multi-component Laves phase in a dual-phase refractory high-entropy alloy CrHfNbTaTi)
Yamanaka, K. & Chiba, A.
23/2/15
1 次の項目: メディア掲載
プレス/メディア
Research from Tohoku University Yields New Study Findings on Alloys (Dislocation Density of Electron Beam Powder Bed Fusion Ti-6Al-4V Alloys Determined via Time-Of-Flight Neutron Diffraction Line-Profile Analysis)
Yamanaka, K., Sato, S. & Chiba, A.
23/2/8
1 次の項目: メディア掲載
プレス/メディア
New Additive Manufacturing Data Have Been Reported by Researchers at Tohoku University (Solidification Behavior and Porosity In Electron-beam Powder Bed Fusion of Co-cr-mo Alloys: Effect of Carbon Concentrations)
Yamanaka, K. & Chiba, A.
22/11/9
1 次の項目: メディア掲載
プレス/メディア
Researchers at Tohoku University Have Published New Data on Materials Research (Demonstrating a duplex TRIP/TWIP titanium alloy via the introduction of metastable retained b-phase)
Yamanaka, K., Sato, S. & Chiba, A.
22/11/8
1 次の項目: メディア掲載
プレス/メディア

山中謙太

フィンガープリント

過去5年の共同研究と上位研究分野

詳細を開く

Preparation of recycled zirconia powders for use in esthetic dental restorations by wet ball milling technique

A novel two-step process for enhancing adhesion strength of cold-spray metallization of carbon fiber-reinforced plastics

Comparative evaluation of powder spreading strategies to enhance powder bed quality in powder bed fusion additive manufacturing: A DEM simulation study

Comparative study on the microstructural evolution and performance of Cu-5Ag wires during cold-drawing from powder metallurgy and cast states

Design and characterization of novel Ti-8Mo-xFe-yCu alloys as implant materials: Evaluation of biocompatibility, mechanical properties, and antibacterial potential

Investigators at Tohoku University Report Findings in Additive Manufacturing (Effect of Powder Morphology On Flowability and Spreading Behavior In Powder Bed Fusion Additive Manufacturing Process: a Particle-scale Modeling Study)

Researchers from Tohoku University Publish Research in Materials and Design (Competition between solid solution and multi-component Laves phase in a dual-phase refractory high-entropy alloy CrHfNbTaTi)

Research from Tohoku University Yields New Study Findings on Alloys (Dislocation Density of Electron Beam Powder Bed Fusion Ti-6Al-4V Alloys Determined via Time-Of-Flight Neutron Diffraction Line-Profile Analysis)

New Additive Manufacturing Data Have Been Reported by Researchers at Tohoku University (Solidification Behavior and Porosity In Electron-beam Powder Bed Fusion of Co-cr-mo Alloys: Effect of Carbon Concentrations)

Researchers at Tohoku University Have Published New Data on Materials Research (Demonstrating a duplex TRIP/TWIP titanium alloy via the introduction of metastable retained b-phase)

山中 謙太

フィンガープリント

過去5年の共同研究と上位研究分野

研究成果

プレス/メディア

山中謙太